Engine and Transmission

g40 timing can't fit belt

Started by paulpolo

Replies: 11
Views: 12,799

December 04, 2014, 10:33:52 AM
by paulpolo

G40 eating rotor arms! After pulley and chip upgrade.

Started by flipout

Replies: 12
Views: 7,912

December 03, 2014, 11:54:56 AM
by JoeH

Advice on engine setup

Started by Matty!

Replies: 6
Views: 6,908

December 01, 2014, 04:01:56 PM
by Matty!

Oil leak from intercooler.

Started by Merrick

Replies: 10
Views: 7,404

November 30, 2014, 05:49:17 PM
by Merrick

fitting GT inlet

Started by Jacque

Replies: 7
Views: 6,261

November 27, 2014, 07:14:36 PM
by JoeH

Pics of idle control valve pipe work ?

Started by John-125

Replies: 1
Views: 4,813

November 27, 2014, 04:51:41 PM
by SuperMario

cambelt snapped

Started by packers

Replies: 2
Views: 5,065

November 24, 2014, 07:40:59 PM
by physicsfool

overfuelling..... why?

Started by vwmk3jon

Replies: 0
Views: 5,024

November 21, 2014, 04:10:02 PM
by vwmk3jon

Longer 5th gear

Started by Ä‘uro

Replies: 0
Views: 5,247

November 14, 2014, 11:05:45 AM
by Ä‘uro

co pot. buy new, used or repair

Started by C0UP3

Replies: 5
Views: 7,157

November 03, 2014, 05:27:01 PM
by G40supercharged

Went from 10W60 to 10W40, now oilbuzzer problems

Started by Victor-J

Replies: 5
Views: 7,531

October 31, 2014, 11:13:42 PM
by Victor-J

Stainless Manifold fitting

Started by ashmang40

Replies: 14
Views: 11,340

October 24, 2014, 02:56:13 PM
by Jacque

oil pump bolts

Started by hayesey

Replies: 7
Views: 6,259

October 21, 2014, 09:32:37 AM
by hayesey

injector o rings

Started by C0UP3

Replies: 4
Views: 4,971

October 16, 2014, 12:35:00 PM
by Merrick

HELPO! Eradic idle after de-wedging throttle body

Started by Merrick

Replies: 6
Views: 6,521

October 06, 2014, 04:40:51 PM
by Merrick

Camshaft!! Which is best?

Started by Merrick

Pages1 2

Replies: 21
Views: 13,088

October 01, 2014, 11:23:29 AM
by Jezza-7

PEC Rods Big End Cap Bolts - Torque Settings Required

Started by dan1300r

Replies: 0
Views: 5,529

September 30, 2014, 08:53:47 AM
by dan1300r

Gear linkage set up

Started by cookie79

Replies: 3
Views: 4,717

September 29, 2014, 04:49:32 PM
by cookie79

Oil Pressure Light - Left Hand Bend

Started by Matty!

Replies: 8
Views: 7,910

September 28, 2014, 03:12:59 PM
by Alex

Oil flashing light and water temperature.

Started by GR40

Replies: 1
Views: 4,605

September 28, 2014, 01:24:19 PM
by Alexiskayak_7