1994 polo cl coupe converted to a g40 - now breaking
no tax or MOT as it failed the other week, i've sorted most bits out, just needs new cv joint (the MOT sheet just says it needs the cv boot but the cv clicks on full lock) and tyre on drivers side
charger was rebuilt by the previous owner approx 1500 miles ago
new clutch and 4-1 stainless steel manifold fitted in september
de-wedged throttle body
65mm pulley
Has got a chip in it but not sure what it is (will try and find out later)
250cc injectors
oil catch tank
headgasket was done in august, along with the cambelt and water pump
the engine was rebuilt 3 - 4 years ago
the drivers side drive shaft is an uprated one
rear coilovers off a golf
did have lowering springs on the front but 1 got nicked whilst it was off the road a couple of years ago so its on standard front suspension
clear front and side indicators
big chin spoiler/splitter with DRL fitted (not wired up, just need some male spade connectors)
de-badged grill
the roof, door handle inserts and rear VW badge were painted cadbury's matte purple but i sprayed them all matte black yesterday (roof needs another coat but i've run out of paint)
it has got a few bits of filler here and there just to try and get rid of some dents
the only spots of rust are on the passenger door where someone tried to break into it (and failed), they are both about the size of a 20p.
i've probably missed quite a few bits but will add anything that i remember.
if i get enough interest in it i will break
only selling because i've got a baby on the way and i want to go back to a land rover
provisionally sold are :-
bottom end
inlet manifold
throttle body
plastic intake pipe
brake servo pipe
gearbox
injectors
pulleys
engine loom and ecu
exhaust manifold (possibly)
All other parts are available.
Located in Bury, Lancs
Hi, has the charger been ported or just serviced???, Would it be possible to come and view the car as i am only located in Bolton cheers Nick.
Hi Nick,
The charger is standard, it was just serviced.
Yes you can come and look anytime, pm me and let me know when and i'll send you my address.
Cheers
Tom
Now breaking
Whats the tailgate like?
Its pretty good, been de-badged and de-wipered.
Price for starter motor and driveshafts please
I need to check if it is an uprated driveshaft or not first, and someone else may have already got first dibs on the one uprated shaft but will let you asap.
Cheers
Tom
hi what are the front doors like?
Hi I'm after the oil breather off the block but hard to get off without damaging and the long starter bolt that goes through the gearbox
Have u sold the loom? If not how much do u want for it? Cheers bud
Quote from: rumsam2006 on June 21, 2012, 09:00:11 AM
Have u sold the loom? If not how much do u want for it? Cheers bud
Which one, engine, interior, rear, full??
Quote from: Jay19gte on June 21, 2012, 12:11:45 AM
Hi I'm after the oil breather off the block but hard to get off without damaging and the long starter bolt that goes through the gearbox
Sorry but the block has already sold.
Will have to see if i've still got that bolt.
Quote from: dan182 on June 19, 2012, 07:34:28 AM
hi what are the front doors like?
Front doors are staying on the car sorry.
Any badges?
Got the front grill badge in the door pocket and can get the boot badge too (although its not on this polo).
Just engine and headlight cheers
Sorry but they've already sold.
Cheers
Tom
Main bits that have already gone :-
Block
Inlet manifold
Throttlebody
Plastic intake pipe
ECU and loom
Gearbox
Starter motor
Alternator
Rocker cover
Supercharger (pending payment)
Badges
Main bits that are still here :-
Injectors (250cc)
65mm pulley set with belts
TA Technix 4-2-1 manifold
Complete cylinder head
Uprated driveshaft
What you want for the cylinder head pal?
£200 ono
Any pictures of the 4-2-1?
Haven't got any of it off the car but have got one with it still on the engine.
pm me your email address and i'll send it to you.
It's a TA Technix one btw.
i am looking for door card got cash wateing
I've seen that TA Technix manifold (as I had some parts from Tom) and it's a beaut. Well made and hardly used, I can vouch for that.
Ross.
got the new clutch and 4-1 stainless steel manifold still? and how much?
Yeah both still here, £120 for both
Rear badge set? :) pm me!
Went a while ago sorry
what uprated driveshaft have you got (is it from a particular group buy?)and how much were you after for it?
front splitter?
Sorry driveshaft went a while ago and front splitter is staying on the bumper (and car) sorry.
If bits aren't gone by next weekend then it's all getting scrapped.
List of whats left here :-
http://www.polog40.co.uk/forum/index.php/topic,8733.0.html
need a box how much ,and is it g40 or gt ?
thanks john 079233324765
hye mate you still got the 250cc injectors?
im interested
cheers
and cost of coil overs please
Hello tbpolo,
could you please confirme if you have the two exterior strips on the roof.
Thanks very much,
Gblue
Quote from: johnbolton38 on August 16, 2012, 12:09:32 AM
need a box how much ,and is it g40 or gt ?
thanks john 079233324765
Cardboard, can write g40 on the box if you want?
Quote from: brookesg40 on August 17, 2012, 07:54:16 AM
hye mate you still got the 250cc injectors?
im interested
cheers
Injectors are gone sorry.
And coilovers are staying on the car now as a project.
Quote from: G40BLUE on August 17, 2012, 07:56:35 AM
Hello tbpolo,
could you please confirme if you have the two exterior strips on the roof.
Thanks very much,
Gblue
I have got them, however i need to decide if i'm de-guttering the roof.
I know there is some purple paint overspray in the inner edge of both strips.
Cheers
Tom